Measured-Data Acquisition
 
   EASYBus PC-Master
 

EASYBus PC-Masters representing the interface between sensor module, EASYBus and PC. To meet customers' various requirements the following options are available :

EBW 9

  • level converter RS232 - EASYBus

  • current supply for up to 9 sensor modules

  • Software EBS 9M

EBW 64 E

  • level converter RS232/RS485 - EASYBus

  • current supply for up to 9 transmitter

  • Software EASYControl

EBW 240

  • level converter RS232/RS485 - EASYBus

  • current supply for up to 240 transmitter

  • Software EASYControl

Specification :
 

EBW 240

EBW 64 E

EBW 9
Voltage supply

230V/50Hz

230V/50Hz

230V/50Hz
Power consumption app. 30W app. 20W app. 5W
Max. permissable number of sensor modules 240 64 9
Permissable cable length* 1000m 1000m 200m
Baud rate 4800 Baud 4800 Baud 4800 Baud
Ambient conditions      
   Operating temperature 0 - 50°C 0 - 50°C 0 - 50°C
   Storage temperature - 20..+ 70°C - 20..+ 70°C - 20..+ 70°C
   Humidity      20 - 80%        non-condensing        20 - 80%        non-condensing       20 - 80%        non-condensing
Serial interface RS232 or RS485 RS232 RS232
Electr. insulated yes yes yes
Overload display yes no no
Short-circuit proof yes conditional yes
Dimensions ( L x W x H )   160x140x80mm 112x80x45mm
 

* depending on type of cable and wiring
 
  EASYControl
 

Software for recording, monitoring, display and documentation of up to 240 sensor modules of the EB-Series, and/or 15 GIA/GIR ... units :

  • min./max. value monitoring for each measuring point

  • straightforward display of current measuring values in form of table

  • simple sorting of sensor module sequence by means of drag and drop

  • scanning cycle for each sensor module can be individually selected

  • adding and deleting of sensor modules during recording operation

  • display of measuring values as diagramm or table

  • separate fault list

  • memorizing, filing and exporting of measuring data, fault lists and settings

  • automatic detection of new transmitters

  • automatic system initialization

  • automatic detection of all sensor modules connected

  • fully automatic assignation and administration of bus addresses

  • aut. detection of transmitter type, meas. range and meas. unit

  • also suitable for monitoring up to 15 GIA/GIR units ( functions limited )

The only thing left for you to do is entering your description !

 
 
  EBS 9M ( nine-channel )
 

Together with a personal computer, an indicator or control unit EB2000 MC or PC-MASTER EBW9 ( Windows software EBS 9M already included ) and sensor modules of the EB series this software makes an extremely comfortable and inexpensive multi-channel system for the acquisition and recording of measuring data. The software EBS 9M includes both funtional modules, i.e. recorder and data display.

System requirements :

As of 486/33 MHz, 8 MB RAM, approx. 7 MB free on hard disk, 3,5" floppy disk drive, VGA-graphics card with a resolution of 800 x 600 or 640 x 480 pixels, MS-Windows 3.1 or higher, serial interface, mouse (recommended)
 
 Data recordings with remote control, remote reading, min./max. alarm etc.
 

Application: e.g. for cooling chambers or other store rooms, cooling cells etc. where recording and monitoring is mandatory

Advantages :

  • Remote control and monitoring e.g. in your office of up to 9 rooms, (use 2 x EB2000MC for more rooms)
  • Both current and min. and max. values will be stored and are accessable for each channel
  • Alarm monitoring for any sensor/logger by means of the EB2000MC
  • Min./max. alarm can be programmed individually for each sensor/logger
  • Remote read out possible for each logger connected

 

  Example for an installation

 

( For enlargement please click on the plan )